IP & Networking

Subnet Calculator (IPv4 and CIDR)

Enter an IPv4 address with a prefix or subnet mask to get the network, broadcast, masks and usable host range, then split it into smaller subnets.

Calculate a subnet

Calculated in your browser. Accepts 192.168.1.10/24, 192.168.1.10 255.255.255.0, or an address plus the prefix list.

Address
192.168.1.10/24
Address type
Private (RFC 1918)
Network address
192.168.1.0
Broadcast address
192.168.1.255
Subnet mask
255.255.255.0
Wildcard mask
0.0.0.255
CIDR notation
192.168.1.0/24
Total addresses
256
Usable hosts
254
Usable range
192.168.1.1 - 192.168.1.254

Binary view

Address: 11000000.10101000.00000001.00001010
Subnet mask: 11111111.11111111.11111111.00000000
Network: 11000000.10101000.00000001.00000000

Network bits are shown in blue, host bits in grey.

Split into smaller subnets

How to use the subnet calculator

  1. Type an IPv4 address with a prefix, such as 10.20.30.40/27, or with a mask, such as 10.20.30.40 255.255.255.224.
  2. Select Calculate. Changing the prefix list recalculates straight away.
  3. To plan smaller networks, choose a new prefix length under Split into smaller subnets.

Worked examples

  • 192.168.1.10/24: network 192.168.1.0, broadcast 192.168.1.255, 254 usable hosts from 192.168.1.1 to 192.168.1.254.
  • 10.20.30.40/27: network 10.20.30.32, broadcast 10.20.30.63, 30 usable hosts from 10.20.30.33 to 10.20.30.62.
  • Splitting 192.168.10.0/24 into /26 gives four subnets of 62 usable hosts: .0, .64, .128 and .192.

What each result means

  • Network address: the first address in the block, which identifies the subnet itself.
  • Broadcast address: the last address, used to reach every host on the subnet.
  • Subnet mask: the prefix written as four numbers; /24 is 255.255.255.0.
  • Wildcard mask: the mask inverted, as used in Cisco access lists and OSPF network statements; /24 is 0.0.0.255.
  • Usable hosts: normally the total minus the network and broadcast addresses. Two special cases: a /31 has two usable addresses for point-to-point links under RFC 3021, and a /32 is a single host.
  • Address type: whether the address is private (RFC 1918), shared carrier-grade NAT space, documentation, multicast or another special-purpose range from the IANA registry, or public.

Choosing a subnet size

Size each VLAN for the devices it will hold in a few years, plus headroom: a /24 suits most office floors, a /26 or /27 suits a small branch or a server segment, and /30 or /31 suits router links. Separate guest, IoT, server and management networks rather than putting everything on one large subnet; our guide to network segmentation explains why.

Troubleshooting

  • "Not a valid IPv4 address". Each part must be 0 to 255, without leading zeros: write 10.1.1.1, not 10.01.1.1, because some systems read leading zeros as octal.
  • "Not contiguous". A mask such as 255.0.255.0 has no CIDR form; real subnet masks are all ones followed by all zeros.
  • IPv6 addresses. This calculator handles IPv4 only. An IPv6 prefix of length n contains 2128−n addresses, and a /64 is the standard size for a single LAN segment.

Frequently asked questions

How many usable hosts are in a /24?

254. A /24 has 256 addresses; the first is the network address and the last is the broadcast address.

Why does a /31 show two usable hosts?

RFC 3021 allows /31 subnets on point-to-point links, where no network or broadcast address is needed, so both addresses are usable.

What is the difference between a subnet mask and a wildcard mask?

They are inverses. A subnet mask marks the network bits with ones; a wildcard mask marks the bits that may vary with ones, which is how Cisco access lists and OSPF match ranges.